Recipe: Soothing cleansing milk

Ultra-friendly make-up removal for sensitive skin

Ingredient list
Recipient: Small tank (250mL)
Choose the desired quantity : mL

Containers to use:
1 x Flacon (100 mL)
Cost: 9.29 € 9.290000000000001 EUR



90 days

9.29 €

Score YUKA
100 / 100
Share the recipe


DERMOPROTECT anti-inflammatory agent: Cosmos-certified 100% natural active ingredient with anti-microbial and highly moisturizing properties to replace conventional preservatives.

The two agents (anti-inflammatory DERMOPROTECT and softener BACTIPROTECT) in addition to their benefits, allow the preservation of the products while respecting sensitive skin! Preservation tests have been carried out in the laboratory to assess their effectiveness. The products keep for 3 months.

List INCI :

Aqua, Prunus Amygdalus Dulcis Oil, Glycerin, Pentylene Glycol, Cetearyl Alcohol, Glyceryl Stearate, Sodium Lauroyl Glutamate, Stearic Acid, Sodium Levulinate, Propanediol, Lactid Acid, Sodium Anisate, Xanthan Gum, Lactobacillus Fermet Lysate

The realization of this recipe is under the responsibility of the user and is not intended for commercial purposes.


For a first use, test your skin's tolerance to this new product by applying a small amount in the bend of the elbow. Wait 24 hours to confirm the absence of reaction, without reaction use the product normally.
Apply morning and evening before your treatment, on previously cleansed skin.

For a complete SENSITIV' routine:
In targeted care: once or twice a week, use the soothing mask
In daily care in the morning: Soothing anti-redness serum Soothing face cream
In daily care in the evening: Soothing cleansing milk Soothing anti-redness serum Soothing face cream

Precautions before starting

Before starting, it is advisable to clean and disinfect the work surface and the utensils: the prepared products will go on the skin, it is therefore necessary to avoid any microbial contamination!

Thoroughly clean the BeautyMix. Then, soak a clean cloth in 70° alcohol (available in supermarkets) and use it to disinfect the BeautyMix tank and all the utensils. Let dry.

Clean the work surface and remove objects that could get in the way.

Place a clean paper towel on the work surface, and place the utensils on it. Have available: a clean teaspoon or spatula, and a clean, dry container for pouring the preparation once ready. Wash hands thoroughly.

Respect the dosages indicated for the ingredients of the recipe.
Need more information ? Consult the "Getting Started" page.
Suggested products
Thoroughly disinfect the work surface, the utensils and the BeautyMix with 70° alcohol and clean paper.
Place the flat mixer in the BeautyMix bowl. Place the bowl on the scale.
Switch on the scale then perform the tare (zero) by pressing the T key.
Be careful, for this recipe, the glycerin must be weighed on one side of the tank and not on the mixer. Weigh the required amount of glycerine into the tank
5.0 g
Press the T key, weigh the required amount of thickener on the glycerin, avoid the mixer
0.1 g
Take the tank then using a spatula, mix the thickener and the glycerin until the two ingredients are homogenized.
Press T, then add the required amount of water
69.9 g
Place the bowl on the BeautyMix and press the button twice to start the blue program.
At the end of the program, take the bowl and put it on the scale.
Press T, then add the sweet almond oil
10.0 g
Press T, and add the fluid cream emulsifier
8.0 g
Place the tank on the BeautyMix, and press the button 3 times to launch the red program and wait for the BeautyMix to stop on its own. If everything is not completely melted at the end of the program, run it again.
Launch the blue program.
At the end of the program, take the lid of the tank then put it on the scale and put the tank on it (the scale being sensitive to heat, this prevents the weighing from being distorted).
Perform the tare (zero) by pressing the T key. Add the Fortifying BIOPROTECT active ingredient
2.0 g
Press T, then add BACTIPROTECT antimicrobial agent
3.0 g
Press T, then add DERMOPROTECT antimicrobial agent
3.0 g
Homogenize with the blue program by pressing twice, then restart the blue program a second time. And finally transfer the mixture into a clean bottle with the pump.
And There you go !